Inicio / Bronze / Bronze sheets

Bronze sheets

Laminated bronze sheet for decorative applications.

Data sheet: Bronze sheets

Laminated bronze sheets are widely used in the decorative sector for their aesthetic finish, durability and versatility. They offer a visually appealing appearance that can range from glossy to matt finishes, depending on the surface treatment applied. In addition, they can be used in both interior and exterior applications due to the corrosion resistance of the material of manufacture.

Despite their durability, bronze sheets are relatively malleable, allowing them to be cut, bent and shaped to create complex and detailed designs, making them suitable for a variety of decorative applications. And, over time, bronze develops a natural ageing that can add character and depth to the piece. In addition to its use in decorative panels, laminated bronze sheets are used in signage, furniture, column cladding, and in the creation of works of art, among others.

Material Designation		Chemical Composition in % (m/m)																	Density g/cm³
Symbolic	Numerical	Element	Cu	Al	As	Be	C	Co	Fe	Mn	Ni	P	Pb	S	Si	Sn	Zn	total others	approx.
CuSn4	CW450K	min.	Rest	-	-	-	-	-	-	-	-	0,01	-	-	-	3,5	-	-	8,9
CuSn4	CW450K	max.	-	-	-	-	-	-	0,1	-	0,2	0,4	0,02	-	-	4,5	0,2	0,2	8,9
CuSn5	CW451K	min.	Rest	-	-	-	-	-	-	-	-	0,01	-	-	-	4,5	-	-	8,9
CuSn5	CW451K	max.	-	-	-	-	-	-	0,1	-	0,2	0,4	0,02	-	-	5,5	0,2	0,2	8,9
CuSn6	CW452K	min.	Rest	-	-	-	-	-	-	-	-	0,01	-	-	-	5,5	-	-	8,8
CuSn6	CW452K	max.	-	-	-	-	-	-	0,1	-	0,2	0,4	0,02	-	-	7	0,2	0,2	8,8
CuSn8	CW453K	min.	Rest	-	-	-	-	-	-	-	-	0,01	-	-	-	7,5	-	-	8,8
CuSn8	CW453K	max.	-	-	-	-	-	-	0,1	-	0,2	0,4	0,02	-	-	8,5	0,2	0,2	8,8
CuSn3Zn9	CW454K	min.	Rest	-	-	-	-	-	-	-	-	-	-	-	-	1,5	7,5	-	8,8
CuSn3Zn9	CW454K	max.	-	-	-	-	-	-	0,1	-	0,2	0,2	0,1	-	-	3,5	10,0	0,2	8,8

EN		DIN		ASTM	BS	JIS	SN
Symbolic	Numerical	Symbolic	Numerical	ASTM	BS	JIS	SN
CuSn5	CW451K	-	-	C51000	PB102	C5102	CuSn5
CuSn4	CW450K	CuSn4	2.1016	C51100	PB101	C5111	-
CuSn6	CW452K	CuSn6	2.1020	C51900	PB103	C5102	CuSn6
CuSn8	CW453K	CuSn8	2.1030	C52100	PB104	C5212	-
CuSn8	CW453K	CuSn8	2.1030	C52100	PB104	C5210	-
CuSn5Pb1	CW458K	-	.	C53400	-	C5341	CuSn5Pb1
CuSn4Pb4Zn4	CW456K	-	.	C54400	-	C5441	CuSn4Pb4Zn4
CuAl9Ni3Fe2	CW304G	-	-	-	-	-	-
CuAl10Fe1	CW305G	SG-CuAl10Fe	2.0937	C61800	CA103	-	CuAl10Fe1
CuAl10Fe3Mn2	CW306G	CuAl10Fe3Mn2	2.0936	-	-	-	CuAl10Fe3Mn2
CuAl10Ni5Fe4	CW307G	CuAl10Ni5Fe4	2.0966	C63000	-	-	CuAl10Ni5Fe4
CuAl11Fe6Ni6	CW308G	CuAl11Fe6Ni6	2.0978	-	-	-	-

Designations			Nominal thickness mm		Tensile Strength R_m N/mm²		Yield Limit at 0,2% R_p0.2 N/mm²	Elongation A_{50 mm} para Thicknesses up to 2,5mm inc. % min.	A for thicknesses greater than 2.5mm % min.	Hardness HV		Grain size mm
Material		Metallurgical State	Nominal thickness mm		Tensile Strength R_m N/mm²					Hardness HV		Grain size mm
Symbolic	Numerical	Metallurgical State	from	up to and including	min.	max				min.	max	min.	max.
CuSn4	CW450K	R290	0,1	5	290	390	(max. 190)	40	50	-	-	-	-
		H070			-	-	-	-	-	70	100	-	-

		R390	0,1	5	390	490	(min. 210)	11	13	-	-	-	-
		H115			-	-	-	-	-	115	155	-	-

		R480	0,1	5	480	570	(min. 420)	4	5	-	-	-	-
		H150			-	-	-	-	-	150	180	-	-

		R540	0,1	2	540	630	(min. 490)	3	-	-	-	-	-
		H170			-	-	-	-	-	170	200	-	-

		R610	0,1	2	610	-	(min. 540)	-	-	-	-	-	-
		H190			-	-	-	-	-	190	-	-	-
CuSn5	CW451K
		R310	0,1	5	310	390	(max. 250)	45	55	-	-	-	-
		H075			-	-	-	-	-	75	105	-	-

		R400	0,1	5	400	500	(min. 240)	14	17	-	-	-	-
		H120			-	-	-	-	-	120	160	-	-

		R490	0,1	5	490	580	(min. 430)	8	10	-	-	-	-
		H160			-	-	-	-	-	160	190	-	-

		R550	0,1	2	550	640	(min. 510)	4	-	-	-	-	-
		H180			-	-	-	-	-	180	210	-	-

		R630	0,1	2	6340	720	(min. 600)	2	-	-	-	-	-
		H200			-	-	-	-	-	200	230	-	-

		R690	0,1	2	690	-	(min. 670)	-	-	-	-	-	-
		H220			-	-	-	-	-	220	-	-	-
CuSn6	CW452K
		R350	0,1	5	350	420	(max. 300)	45	55	-	-	-	-
		H080			-	-	-	-	-	80	110	-	-

		R420	0,1	5	420	520	(min. 260)	17	20	-	-	-	-
		H125			-	-	-	-	-	125	165	-	-

		R500	0,1	5	500	590	(min. 450)	8	10	-	-	-	-
		H160			-	-	-	-	-	160	190	-	-

		R560	0,1	2	560	650	(min. 500)	5	-	-	-	-	-
		H180			-	-	-	-	-	180	210	-	-

		R640	0,1	2	640	730	(min. 600)	3	-	-	-	-	-
		H200			-	-	-	-	-	200	230	-	-

		R720	0,1	2	720	-	(min. 690)	-	-	-	-	-	-
		H220			-	-	-	-	-	220	-	-	-
CuSn8	CW453K
		R370	0,1	5	370	450	(max. 300)	50	60	-	-	-
		H090			-	-	-	-	-	90	120	-

		R450	0,1	5	450	550	(min. 280)	20	23	-	-	-
		H135			-	-	-	-	-	135	175	-

		R540	0,1	5	540	630	(min. 460)	13	15	-	-	-
		H170			-	-	-	-	-	170	200	-

		R600	0,1	5	600	690	(min. 530)	5	7	-	-	-
		H190			-	-	-	-	-	190	220	-

		R660	0,1	2	660	750	(min. 620)	3	-	-	-	-
		H210			-	-	-	-	-	210	240	-

		R740	0,1	2	740	-	(min. 700)	2	-	-	-	-
		H230			-	-	-	-	-	230	-	-

TOLERANCES ON THICKNESS OF HOT-ROLLED PRODUCTS

Nominal thickness		Tolerances on thickness, for nominal widths of
Nominal thickness		Up to and including 700		Greater than 700, up to and inc. 1000		Greater than 1000, up to and inc. 1500		Greater than 1500
greather than	up to and including	1)	2)	1)	2)	1)	2)	Greater than 1500
-	2,5	By agreement		By agreement		By agreement		By agreement
2,5	5,0	± 0,25	± 0,30	± 0,30	± 0,35	± 0,35	± 0,45
5,0	7,5	± 0,35	± 0,45	± 0,40	± 0,50	± 0,45	± 0,55
7,5	10	± 0,45	± 0,60	± 0,50	± 0,65	± 0,55	± 0,75
10	15	± 0,75	± 0,95	± 0,80	± 1,00	± 0,90	± 1,10
15	25	± 0,95	± 1,20	± 1,05	± 1,30	± 1,30	± 1,60
25	50	± 1,30	± 1,60	± 1,40	± 1,75	± 1,50	± 1,90
50	-	± 1,50	± 1,90	± 1,65	± 2,05	± 1,80	± 2,20
1) For all materials, except CuAl8Fe3 (CW303G), CuNi10Fe1Mn (CW352H), CuNi30Mn1Fe (CW354H) y CuZn20Al2As (CW702R)
2) For all alloys CuAl8Fe3 (CW303G), CuNi10Fe1Mn (CW352H), CuNi30Mn1Fe (CW354H) y CuZn20Al2As (CW702R)

TOLERANCES ON THICKNESS OF COLD ROLLED PRODUCTS

Nominal thickness		Tolerances on thickness, for nominal widths of ^a
greather than	up to and including	Up to and including 350	greather than 350 Up to and including 700	Greater than 700, up to and inc. 1000	Greater than 1000, up to and inc. 1250
0.1^b	0,2	± 0,018	-	-	-
0,2	0,3	± 0,022	± 0,03	± 0,04	-
0,3	0,4	± 0,025	± 0,04	± 0,05	± 0,07
0,4	0,5	± 0,03	± 0,05	± 0,06	± 0,08
0,5	0,8	± 0,04	± 0,06	± 0,07	± 0,09
0,8	1,2	± 0,05	± 0,07	± 0,09	± 0,10
1,2	1,8	± 0,06	± 0,08	± 0,10	± 0,11
1,8	2,5	± 0,07	± 0,09	± 0,11	± 0,13
2,5	3,2	± 0,08	± 0,10	± 0,13	± 0,17
3,2	4,0	± 0,10	± 0,12	± 0,15	± 0,20
4,0	5,0	± 0,12	± 0,14	± 0,17	± 0,23
5,0	6,0	± 0,14	± 0,16	± 0,20	± 0,26
6,0	7,0	± 0,16	± 0,19	± 0,23	± 0,29
7,0	8,0	± 0,18	± 0,22	± 0,26	± 0,32
8,0	9,0	± 0,20	± 0,25	± 0,29	± 0,35
9,0	10,0	± 0,22	± 0,28	± 0,32	± 0,38
^a For all alloys CuAl8Fe3 (CW303G), CuNi10Fe1Mn (CW352H), CuNi30Mn1Fe (CW354H) y CuZn20Al2As (CW702R), tolerances on thickness must be multiplied by 1.25 and the redult rounded up to 0.01mm
^b includes 0.1.
NOTE - For thicknesses greater than 10 mm, tolerances are those indicated in Norm EN 1653.

Documentation download

Title

Other languages

Type

Created

INDUSTRIAL SECTOR Bronmetal

Type Catalogue

Created 07/07/2020

Bronze sheets

Type Technical sheets

Created 03/07/2020

Selection of sheets in different alloys

Type Technical sheets

Created 29/03/2022

Bronze sheets

Data sheet: Bronze sheets

TOLERANCES ON THICKNESS OF HOT-ROLLED PRODUCTS

TOLERANCES ON THICKNESS OF COLD ROLLED PRODUCTS

Documentation download

Copper sheets

Round extruded/calibrated bronze tubes

Bronze strips